top of page

LumaQuote

Log In Start Free

Ballast Factor: What to Check During a Lighting Audit

Writer: LumaQuote
LumaQuote
Nov 7
5 min read

Ballast factor is the light output of a fluorescent lamp on a particular ballast divided by its output on a reference ballast. Use it to understand the existing lighting output. Use the complete lamp-and-ballast input watts, taken from the matching data-sheet row or a suitable measurement, for the energy baseline.


The examples below are illustrative. Verify the installed equipment, product data and project inputs before using the calculations.


What ballast factor tells an auditor


A ballast factor of 0.88 means the lamp produces about 88% of its reference-ballast light output under the specified test conditions. A factor above 1.00 means output exceeds the reference level. The reference is a test comparison, rather than the amount of useful light reaching a desk.


The Philips Advance ballast fundamentals guide, in its Electronic Ballast Fundamentals section, defines that relationship and treats input watts as a separate characteristic. Photograph the ballast model and lamp marking together so the estimator can find the correct combination.


On a retrofit walkthrough, matching diffusers can hide different ballasts. A warehouse office may have lower-output ballasts while a packing area uses higher-output equipment. Calling the whole floor “two-lamp T8” can flatten those differences and leave the replacement selection short on light in the working area.


The T8 versus T12 guide covers lamp identification. Ballast factor adds another part of the equipment record after the lamp family is known.


Calculate lamp output with the reference lumens


Use the lamp manufacturer's lumen rating on the applicable reference basis. Multiply that figure by ballast factor, then account for the number of lamps operating on that ballast.


For two lamps rated at 3,000 reference lumens each, first calculate 2 × 3,000 = 6,000 reference lumens. Then apply the selected factor. At 0.88, the result is 6,000 × 0.88 = 5,280 lamp lumens.


Ballast factor

Calculation

Calculated lamp output

0.77

6,000 lm × 0.77

4,620 lm

0.88

6,000 lm × 0.88

5,280 lm

1.18

6,000 lm × 1.18

7,080 lm


Lamp-output comparison for 6,000 reference lumens: ballast factors 0.77, 0.88 and 1.18 give 4,620, 5,280 and 7,080 lamp lumens.

With the same 6,000 reference lamp lumens, the three ballast factors produce different calculated lamp outputs.


The calculation is before fixture optical losses. Reflectors, diffusers, dirt, lamp aging and the room geometry affect the installed result. A useful retrofit comparison therefore includes the lighting requirement and distribution as well as lamp output.


Lutron's Fluorescent Dimming Systems Technical Guide, printed pages 6 and 7, explains the lumen calculation and why ballast factor and efficiency are separate measures.


Keep ballast factor, power factor and watts separate


Term

What to use it for

Ballast factor

Relative lamp light output

Power factor

Relationship between real power and apparent power

System input watts

Power used by the complete operating lamp-ballast combination


A ballast marked 0.88 BF is not declaring 88% electrical efficiency. Likewise, a high power factor is not a direct energy-savings percentage. Keep the manufacturer's field names intact when transcribing a label.


In particular, multiplying lamp nameplate watts by ballast factor gives the wrong method for establishing system input. Ballast factor scales the reference light output. The ballast's electrical operation and losses are already represented in the applicable complete-system input specification.


When a data sheet lists several lamp types or lamp counts, match the installed row before copying its watts. Include the supply voltage if the published power varies with voltage. That lookup is where a clear label photo pays off.


A lamp-watts shortcut can overstate savings


Consider an audit group of 40 two-lamp fixtures operating 2,500 hours per year. Each lamp carries a 32 W marking, so adding the lamp markings gives 2 × 32 = 64 W. Assume the equipment review instead establishes 54 W of complete system input for the installed combination, with a proposed LED input of 30 W per fixture.


First calculate the baseline: 40 fixtures × 54 W = 2,160 W. Multiply by 2,500 hours to obtain 5,400,000 Wh, then divide by 1,000 to obtain 5,400 kWh per year.


Next calculate the proposed case: 40 × 30 W = 1,200 W. Multiply by 2,500 hours to obtain 3,000,000 Wh, then divide by 1,000 to obtain 3,000 kWh per year. Subtract the two cases: 5,400 − 3,000 = 2,400 kWh saved annually.


At US$0.16 per avoided kWh, the energy-cost saving is 2,400 × US$0.16 = US$384 per year.


If the estimator enters 64 W instead, the baseline becomes 40 × 64 × 2,500 ÷ 1,000 = 6,400 kWh. Subtracting the same 3,000 kWh proposed case gives 3,400 kWh of claimed savings, worth US$544 at the same rate. The shortcut overstates annual energy savings by 3,400 − 2,400 = 1,000 kWh, or US$160.


Those results cover energy charges only. Keep the tariff, hours, controls and other savings categories documented when moving into the retrofit ROI calculation.


Capture the evidence while you are at the fixture


Keep these details together for each distinct group: the full ballast manufacturer and model, installed lamp code and count, supply voltage, published ballast factor, complete input watts and the source of those values. Add a readable label photo and the area or room reference.


Have qualified personnel handle access to electrical compartments and power measurements using appropriate isolation and safety procedures.


In a stairwell or storage room with frequent switching, also record the starting method and existing controls. Those details help the reviewer assess the operating conditions when comparing repair or conversion options. The magnetic versus electronic ballast guide covers those broader checks.


When the label cannot be read, keep the open question attached to the group. Identify a representative accessible fixture or arrange the required verification before finalizing the baseline. A guessed factor can affect the output comparison, while guessed watts can affect the savings.


Choose the replacement for the room


Use the existing lamp-and-ballast information to understand the starting point, then assess the proposed equipment for the task. Review output, distribution, mounting, controls and fixture condition. A lower wattage is useful when the selected solution provides the lighting the space needs.


DOE's commercial LED purchasing guidance emphasizes application suitability and warns against comparing unlike products solely on efficacy. For a packing bench, check the work surface and shadows. For a corridor, check the spacing and distribution.


In LumaQuote Field, organize fixture counts, photos and notes by area and space, then sync the audit for desktop review. Keeping the lamp and ballast evidence with the group gives the estimator a clear starting point for the replacement and savings calculation.


Start free with one fluorescent area. Capture its equipment details and confirm the system watts before preparing the retrofit estimate.


Frequently asked questions


Can ballast factor be greater than 1?


Yes. It means the lamp's output on that ballast exceeds its output on the reference ballast under the applicable test conditions.


Should every two-lamp T8 fixture use the same baseline watts?


Match the installed lamp-and-ballast combination. Different models, lamp variants and operating configurations can have different input specifications. Separate the audit groups when their equipment differs.


What should I do with a dimming fluorescent system?


Record the ballast and control models, the operating setting and the schedule. Review power at the relevant operating conditions so the baseline reflects how the system is used.


bottom of page