Daylight Harvesting: How It Works and What to Check During a Lighting Audit


Short answer: Daylight harvesting automatically dims or switches electric lighting in response to available daylight. A photosensor measures light, and a controller adjusts a compatible lighting group to support the required illumination. During an audit, identify the fixtures that can respond separately, verify driver compatibility, record shading and operating hours, and include setup and testing in the quote. Calculate the additional controls savings against the proposed lighting baseline, not the original fluorescent or HID load.
Introduction
A bright window wall can make daylight harvesting look like an easy addition to an LED retrofit. The harder questions come when you price it: which fixtures belong in the daylight group, can they dim independently, and who will set up and test the controls?
This guide explains the technology, then follows a 60-fixture office through the audit, savings calculation and controls allowance. It is written for distributors, ESCOs and contractors preparing a commercial retrofit quote.
What is daylight harvesting?
Daylight harvesting, also called daylight-responsive lighting control, reduces electric lighting when daylight can supply part of the light a space needs. It uses light from the sky as well as direct sunlight. A room does not need a sunbeam on the floor to benefit.
The control changes electric light output; it does not generate electricity. Windows, skylights and other openings admit the daylight. The sensor and controller decide how the electric lighting responds.
Leviton's daylighting overview gives a useful manufacturer introduction. For a retrofit, the next step is to establish which existing or proposed fixtures can be controlled together.
How a daylight harvesting system works

Sense the light. A photosensor measures daylight or the combined daylight and electric light, depending on the control approach.
Apply the control settings. The controller uses its configured response, including the target or reference setting, limits and time delays.
Adjust the lighting group. Compatible drivers dim, or switching equipment changes the lighting state. Some products combine sensing and control in one device.
Verify the result. The installer checks the actual task-plane illumination and the response under changing light conditions.
Continuous dimming allows a gradual response. Switching or stepped control changes output in larger increments. The choice depends on the equipment, application and applicable project requirements. ETC's daylight harvesting white paper explains these control methods.
Open-loop vs closed-loop daylight harvesting
The distinction is what the sensor sees, not the size of the building.
Approach | Sensor input | What to check during the audit |
|---|---|---|
Open-loop | Daylight, with the controlled electric lighting excluded from its view | Window or skylight relationship, sensor orientation, shades, and whether its reading represents the controlled area |
Closed-loop | Combined daylight and electric light reflected within the controlled space | Field of view, task locations, partitions, reflective surfaces and feedback from the controlled fixtures |
Hybrid or product-specific | A combination defined by the manufacturer | Exact model, supported operating mode and the manufacturer's placement and setup instructions |
Open-loop sensors can be indoors or outdoors. Closed-loop sensors are normally inside the controlled space. Neither label establishes how many fixtures a sensor can serve or guarantees better performance in every room.
A ceiling sensor's reading is also not automatically the illuminance on a desk. Casambi's setup guidance explains how sensor readings, task-surface measurements and control targets can differ. Follow the selected manufacturer's method rather than copying a lux setting between rooms.
Where daylight harvesting is worth investigating
Look for daytime lighting use that overlaps with useful daylight: perimeter offices, classrooms, retail areas and spaces with skylights are sensible places to investigate. A deep interior room or a mostly night-shift operation has less opportunity.
During the walkthrough, check what happens on an ordinary working day. Closed blinds, nearby buildings, dirty skylights, tall racks and changing displays can alter the result. Ask occupants about glare and shade use. A sunny photograph records one condition, not the annual savings potential.
Treat daylight control as an option to assess by space. Your commercial lighting controls scope may also include occupancy sensing, scheduling or high-end trim, with different reasons for using each.
Daylight harvesting audit checklist
Record enough detail for another person to understand the proposed control group without revisiting the site. Keep the checklist with your lighting audit records.
Audit item | Record on site | Why it changes the quote |
|---|---|---|
Daylight openings | Window or skylight locations, orientation, head height and obstructions | Helps establish where daylight may be useful and which zones need design review |
Shades and actual use | Blind type, typical position, glare complaints and seasonal changes | Affects how much daylight reaches occupied areas |
Fixture groups | Location reference, quantity, circuit and current control relationship | Shows which lights can respond separately and where rewiring or regrouping may be needed |
Driver and controls | Exact model, voltage, dimming interface, minimum output and off capability | Identifies compatibility work and additional components |
Work surfaces | Task locations, measurement plane and agreed lighting criteria | Provides the reference for setup and verification |
Operating hours | Weekday, weekend, holiday and after-hours operation | Establishes when lighting use overlaps daylight |
Existing strategies | Occupancy, schedules, trim settings and overrides | Prevents assigning the same saved energy to two controls |
Installation access | Ceiling access, lift needs, occupied work restrictions and wiring route | Changes labor, equipment and commissioning allowances |
Take a room overview, a view toward the windows or skylights, and readable equipment-label photos. Record the date, time, sky condition, blind position and electric-light state beside any light-level measurement. The audit photo checklist covers useful location and equipment evidence.
If access or identification is incomplete, mark the item for verification. Do not turn an unreadable driver label into an assumed dimming specification.
Map the daylight group before counting sensors
For a sample office with 60 fixtures, suppose the proposed daylight strategy serves the 20 fixtures nearest the windows. The other 40 remain outside that strategy. They may have separate occupancy or scheduling controls, but they should not automatically receive the daylight savings allowance.

Example control groups: 20 perimeter fixtures and 40 interior fixtures. The drawing does not define code daylight-zone boundaries or sensor quantities.
Give the perimeter group a location reference and separate audit or estimate lines where its controls, watts or hours differ. Record any shared circuit with the interior fixtures as a design or installation issue to resolve.
Write the intended response before choosing devices. For this office, a scope note could read: “During occupied operation, dim the perimeter group as daylight increases and restore output as daylight falls. Keep interior fixtures independently controlled. Confirm the required task illumination, lower limit, off behavior and overrides during design and setup.” Identify emergency lighting separately in the approved control arrangement.
Do not use a universal rule such as “everything within 15 feet of a window.” Daylit-zone definitions depend on the adopted code, geometry and project conditions. Sensor spacing comes from the selected system's instructions and design.
For skylit warehouses, map openings against racking and fixture rows. Our warehouse audit checklist covers the related access and layout checks.
Can the proposed LED fixtures actually dim?
Check the exact driver and control combination. “LED,” “dimmable” and “0–10 V” are not complete compatibility specifications. Confirm the control method, supported load, minimum stable output, off behavior, wiring requirements and emergency-lighting arrangements.
A 50% dimming command does not prove a 50% reduction in input watts. PNNL's research on 0–10 V LED streetlights documents variation between control signals, light output and power in the products it studied. Obtain the relevant performance data for the actual indoor equipment or measure it; do not borrow a dimming curve from a different product.
Calculate daylight harvesting savings separately from LED savings
There is no single savings percentage that belongs in every quote. GSA reports that an LBNL assessment at five federal sites found average annual lighting energy savings of 27% from the evaluated daylight harvesting installations. That finding describes those sites and systems; it is not a default for an entire retrofit project. See GSA's Integrated Daylighting Systems findings.
For an early estimate, use a documented annual-average input-power reduction for the eligible group. It should account for the periods when daylight is weak or absent. Replace it with a more detailed model or monitoring evidence when the project needs greater accuracy.
Additional daylight savings, kWh/year = eligible fixtures × proposed watts per fixture ÷ 1,000 × baseline operating hours × annual-average daylight reduction.
Use the baseline for the scenario being compared. If occupancy or scheduling savings are already included, estimate the additional daylight effect on the remaining energy using consistent time periods. Do not simply add independent savings percentages.
Worked example: a 60-fixture office
These are selected estimating inputs, not measured results, typical prices or a prescribed savings rate:
60 existing fixtures at 100 W system input each.
60 proposed LED fixtures at 40 W input each.
3,000 operating hours per year and US$0.15/kWh.
Daylight controls on 20 of the proposed fixtures.
An assumed 30% annual-average power reduction for that 20-fixture group.
No other controls savings, rebates, demand savings or HVAC effects included.
Scenario | Annual lighting energy | Annual energy cost |
|---|---|---|
Existing lighting | 18,000 kWh | US$2,700 |
LED only | 7,200 kWh | US$1,080 |
LED plus daylight control on 20 fixtures | 6,480 kWh | US$972 |
The LED replacement saves 10,800 kWh/year. Daylight control adds 720 kWh/year, or US$108/year, calculated as 20 × 40 ÷ 1,000 × 3,000 × 0.30.
The 30% assumption applies to one-third of the proposed fixtures. It reduces the whole office's LED-only lighting energy by 10%. Total savings against the original lighting are 64%, not 60% plus 30%.

Worked example: daylight control saves another 720 kWh/year after the LED upgrade. All figures use the inputs listed above.
If the additional installed controls cost is US$600, simple incremental payback is US$600 ÷ US$108 = 5.6 years. Keep that separate from the payback of the LED replacement itself. The retrofit ROI guide explains the broader proposal calculation.
Daylight harvesting savings calculator
Change the eligible-group inputs below to test the additional daylight-control case. The reduction is an annual-average power assumption, not a sensor setpoint or a midday dimming percentage. Results cover lighting energy only, before rebates, maintenance and any added controls standby power.
Put commissioning and handover in the controls price
A sensor price alone is not an installed controls allowance. Build a scope for the group you actually surveyed:
Sensors, controllers, compatible drivers and any required gateways or licenses.
Control wiring, circuit changes, access equipment and installation labor.
Grouping, programming, target settings, override behavior and startup.
Functional checks, required acceptance testing, documentation and user training.
Any agreed return visit to resolve performance issues.
For the US$600 example, an allowance could comprise US$200 of components, US$250 of installation and US$150 of setup and testing. These are selected inputs for the calculation, not market price guidance. Obtain actual supplier and installer costs for the scope.
Agree who verifies task illumination when daylight is low, how the lights respond when daylight increases, and what happens when shades close. Check for distracting repeated dimming or switching. Casambi's documentation, linked above, explains why response sensitivity and tolerance affect behavior under passing clouds.
Handover should identify control groups, settings, override instructions, test results and responsibility for later changes. A changed partition or display may require a review of the setup.
Check code requirements and rebates as separate questions
Whether daylight-responsive controls are required depends on the jurisdiction, adopted edition, project type, affected lighting and applicable exceptions. Record those questions for the responsible designer or code professional before finalizing the scope.
For example, the California Energy Commission publishes a dedicated NRCA-LTI-03-A daylighting-responsive controls acceptance form within its 2025 nonresidential compliance documents. If testing applies to the project, identify the responsible party and include the work in the estimate.
A code requirement does not establish a rebate amount. Confirm the utility, program, exact products, application timing and incentive calculation independently. Use the commercial lighting rebate directory to find the relevant guide, then verify the current program's own documents.
Carry the audit into a quote the customer can review
In LumaQuote, keep fixture counts, photos, hours and controls notes tied to the relevant spaces. Review daylight harvesting as an optional controls strategy and compare the LED-only case with the proposed controls case. The platform overview explains how controls assumptions feed the estimate and proposal.
Record the basis of your reduction assumption, identify unverified compatibility or zoning items, and include installation and commissioning costs. Audit software organizes the project; daylight simulation, final control design and code acceptance remain separate tasks where needed.
For a first test, capture one window-side area in the lighting audit app, then review the counts and notes on desktop. Start with the Free plan and check the current plan inclusions before evaluating paid controls features.
Daylight harvesting FAQs
Is daylight harvesting the same as daylighting?
Daylighting brings natural light into a building through windows, skylights and related design choices. Daylight harvesting controls reduce electric lighting in response to that available light. Adding windows alone does not make an existing lighting system respond automatically.
What is a daylight harvesting sensor?
It is a photosensor that supplies a light-level signal for daylight-responsive control. It may be standalone or integrated into a fixture or control device. The operating mode, field of view and placement must suit the selected system and controlled area.
Is an occupancy sensor the same as a daylight sensor?
No. An occupancy sensor responds to occupancy detection; a daylight sensor responds to light. A combined device can support both strategies. The scope and savings estimate should still identify what each strategy changes.
How much energy does daylight harvesting save?
It depends on the controlled fixtures, daylight availability, hours, shading, settings and existing controls. In this article's example, a 30% reduction on 20 of 60 equal-wattage LED fixtures produces a 10% reduction in whole-room LED lighting energy. That is a calculation example, not a predicted outcome for another building.
Does daylight harvesting need an internet connection?
Not inherently. Some systems operate locally; others use networks, gateways or cloud services for particular functions. Confirm which functions continue if the internet or gateway connection is unavailable, and include any required subscription in the quote.
Can I use a light-level reading from one site visit to predict annual savings?
Not by itself. A reading records one combination of weather, time, shade position and lighting state. Use it to document conditions and plan further checks. Annual savings need a defensible model or operating evidence that accounts for changing daylight and actual use.


