top of page

LumaQuote

Log In Start Free

T5 vs T8: Tube Sizes, Ballasts and LED Replacement Options

Writer: LumaQuote
LumaQuote
Nov 1
6 min read

T5 and T8 describe tube diameter. A T5 is 5/8 inch wide; a T8 is 1 inch wide. For common straight fluorescent lamps, T5 uses a G5 base and T8 uses a G13 base. They need different lampholders and suitable ballasts, so you cannot swap one for the other as a routine relamp.


For a commercial retrofit, the useful comparison goes beyond tube size. Identify the installed lamp, confirm the complete fixture's power draw, and choose a replacement that delivers the required light. A smaller tube does not automatically mean a lower electricity bill.


T5 and T8 tube-end diagrams comparing 5/8-inch and 1-inch diameters and G5 versus G13 bases.
T5 and T8 describe tube diameter. Common straight fluorescent versions also have different bases and pin spacing.

T5 vs T8 at a glance


What to compare

T5 fluorescent

T8 fluorescent

Nominal tube diameter

5/8 inch, about 16 mm

1 inch, about 25.4 mm

Common straight-lamp base

G5 miniature bi-pin

G13 medium bi-pin

Pin spacing, center to center

5 mm

13 mm

Example lamp codes

F28T5 and F54T5HO

F32T8

Important distinction

High-efficiency and high-output versions differ

Wattage and ballast factor vary by system

Direct swap into the other fixture

No

No


GE Lighting's tube selector confirms the diameters, bases and pin spacing. These are identification clues, not a complete replacement specification. Measure the lamp and read its marking before ordering.


If the existing tube is wider than either option, use our T8 vs T12 guide to identify that separate lamp family.


What do T5 and T8 mean?


The T indicates a tubular shape. The number gives the nominal diameter in eighths of an inch:


  • T5: 5 divided by 8 = 0.625 inch.

  • T8: 8 divided by 8 = 1 inch.


That code does not specify the lamp's length, watts, brightness, color temperature or operating circuit. It also does not tell you whether the tube is fluorescent or LED. Read the complete product description.


On a mixed site, one office might have T8 fluorescent troffers while the warehouse has T5HO high bays. Record those as different fixture groups. Combining them under “fluorescent, four-foot” hides information the estimator needs.


T5 HE vs T5 HO: check the letters after the size


T5 high-efficiency, often called HE, and T5 high-output, or HO, lamps share a diameter but serve different output requirements. Common examples in the roughly four-foot fixture class are 28 W T5 HE and 54 W T5 HO. A common North American T8 example is F32T8, rated at 32 W.


Those are lamp ratings. They exclude the ballast and do not establish whole-fixture input power.


For specific examples, SATCO's F28T5 sheet lists 28 W and a G5 base. Signify's F54T5/850/HO sheet lists 54.1 W, while its F32T8 data sheet lists 32 W. Product data takes priority over a rounded lamp-family description.


Bar chart of nominal lamp watts: F28T5 at 28, F32T8 at 32 and F54T5HO at 54, excluding ballasts.
Common lamp ratings illustrate why T5 HE and T5 HO must be distinguished. This is not an efficiency ranking.

A maintenance order for “T5 tubes” is incomplete. Include the full code, length and output family. A T5 HE lamp is not an approved replacement for a T5 HO lamp merely because it fits between the sockets.


Are T5 and T8 tubes interchangeable?


No. Three checks prevent an incorrect substitution.


1. Base and lampholder


G5 and G13 have different pin spacing. A T5 tube will not correctly seat in a T8 lampholder. An adapter does not establish electrical compatibility or make a conversion acceptable by itself.


2. Actual lamp length


Common linear T5 lamps are shorter than T8 lamps sold in a similar nominal fixture class. A description such as “four-foot” can refer to the application rather than an exact end-to-end dimension. Compare the manufacturer's dimension drawing, including its measurement convention.


3. Ballast and wiring


The ballast must support the exact lamp family, wattage and lamp count. Changing tube families can require different lampholders, a different ballast and an approved conversion method. That work belongs in the installation scope, rather than being treated as a lamp-only purchase.


For the differences between the ballast technologies themselves, see magnetic vs electronic ballasts.


Which is brighter or more efficient?


Neither diameter gives a reliable answer on its own.


A high-output T5 lamp can produce substantially more light than a standard-output T8 lamp while also consuming more power. That does not establish which complete fixture provides the required illumination more efficiently.


Compare the following information for the actual products:


Question

Evidence to use

How much electricity does it draw?

Complete lamp-and-ballast input watts, or complete LED system watts

How much light reaches the work?

Luminaire photometry and site light-level checks

Is the light comfortable and suitable?

Distribution, glare, color temperature and color rendering

Will it operate in this space?

Ambient-temperature rating, enclosure and control compatibility


Lamp lumens and luminaire lumens are different measurements. Fluorescent lamp output is affected by the ballast and fixture; LED distribution may also change where the light lands. Do not compare bare-lamp lumens directly with a new fixture's delivered lumens and declare them equivalent.


For a warehouse, check the aisles, racks and task locations using the warehouse lighting audit checklist. A lower wattage is useful only if the proposed lighting still meets the project's needs.


T5 and T8 LED replacements: choose the electrical approach


An LED tube marketed as a T5 or T8 replacement still needs a compatibility review.


Retrofit approach

What stays or changes

Main check before quoting

Type A, ballast compatible

A supported ballast remains

Exact ballast model appears on the lamp maker's compatibility list

Type B, ballast bypass

Ballast is removed or bypassed

Listed lamp, supply voltage, lampholders and wiring match its instructions

Type C, external driver

A separate LED driver powers the lamps

Driver and lamps form a matched system

Retrofit kit or new fixture

More of the lighting assembly changes

Physical fit, listing, light distribution, controls and installation access


Some lamps support more than one approach, but only under their manufacturer's stated conditions. “Works with electronic ballasts” is not enough to approve a Type A tube for every electronic model.


Our Type A vs Type B comparison covers that choice in detail. If the housing or optics also need attention, compare troffer retrofit kits with new fixtures.


Worked example: price the complete T5HO system


Suppose an audit identifies 100 two-lamp T5HO fixtures. For this illustrative estimate, use 120 W per existing fixture, 50 W per proposed LED fixture, 3,600 annual operating hours and $0.15 per kWh. The wattages are example complete-system inputs, not published averages or a product recommendation.


Calculation

Existing lighting

Proposed lighting

Connected load

100 × 120 W = 12 kW

100 × 50 W = 5 kW

Annual electricity

12 × 3,600 = 43,200 kWh

5 × 3,600 = 18,000 kWh

Annual energy charge

$6,480

$2,700


The difference is 25,200 kWh and $3,780 per year in energy charges. That is a calculated result under these assumptions. It excludes demand charges, controls savings, maintenance, taxes and heating or cooling effects.


Example comparing annual electricity of 43,200 kWh at 120 watts per fixture with 18,000 kWh at 50 watts.
With the stated example inputs, the energy-charge difference is $3,780 per year. Verify system watts and lighting performance for the actual site.

The tempting shortcut is to enter 108 W because there are two 54 W lamps. That omits the ballast's effect on the system. Use manufacturer system data or an appropriate verified measurement, and record its source.


Calculate your own lighting energy difference


Change the five inputs below. Enter watts per complete fixture, including the ballast or driver where applicable. The tool estimates electricity use and energy charges; it does not check light levels, product compatibility or rebate eligibility.



What to collect before preparing the quote


  • Full lamp marking, including HE or HO where relevant.

  • Lamp count per fixture and the number of fixtures in each group.

  • Ballast manufacturer, model, input voltage and supported lamp types.

  • Fixture and label photos, attached to the correct room or area.

  • System input watts, annual hours and the evidence behind each assumption.

  • Mounting height, access restrictions, controls and emergency-lighting details.

  • Proposed product, compatibility evidence and any items still requiring verification.


Keep installation costs separate from the energy calculation. A tube conversion that needs wiring, lampholders or a lift is a different job from a routine relamp. The LED retrofit estimating guide shows how to build those costs into the bid.


In LumaQuote's lighting audit software, organize the T5 and T8 groups by area, keep photos and notes with the field record, then review the replacement options before estimating. Start with one representative area so the team can verify the assumptions before repeating them across the site.


T5 vs T8 FAQs


Can I put a T8 tube in a T5 fixture?


No. The common straight fluorescent versions have different bases, pin spacing and ballast requirements. Select the specified lamp or an approved retrofit system for that fixture.


Is T5 always more energy efficient than T8?


No. Compare complete-system watts and useful light output for the actual application. T5 HE, T5 HO and the different T8 systems do not share one universal efficiency ranking.


Does T5 mean fluorescent and T8 mean LED?


No. These codes describe tube diameter. Both names appear on fluorescent products and LED replacement products. The complete product specification identifies the technology and wiring requirements.


Can I replace T5 fluorescent tubes with LED?


Yes, when a suitable product and installation method are available for the existing fixture. Verify the lamp length, base, supply voltage, ballast compatibility or bypass instructions, and the required lighting performance before ordering.


bottom of page